|
|
 |
|
|
USB3.0 CMOS Camere Series
1/1.2 inch 2.35 Mega-Pixels USB3.0 Color / Monochrome
STC-MCS241U3V / STC-MBS241U3V
OMRON SENTECH
|
|
|
|
The STC-MCS241U3V/STC-MBS241U3V features 163 FPS, and a dazzling 2.35 MP resolution.
Utilizing CMOS Global Shutter, the STC-MCS241U3V/STC-MBS241U3V is capable of capturing moving objects without any motion blur.
By utilizing the user friendly USB 3.0 interface, speed and power have never been easier to use.
|
|
| Specifications |
| Model Number |
STC-MCS241U3V(Color) |
STC-MBS241U3V(Monochrome) |
| Image Sensor |
1/1.2″ 2.3M Progressive Color CMOS
(SONY: IMX174))
Spectral Sensitivity Characteristics |
1/1.2″ 2.3M Progressive Monochrome CMOS
(SONY: IMX174))
Spectral Sensitivity Characteristics |
| Active Picture Elements |
1920(H) × 1200(V) |
| Cell Size |
5.86 (H) × 5.86 (V)µm |
| Sync System |
External trigger (Hardware, Software) / Free run |
Maximum
Frame
Rate
(in Full
Scanning
Mode) |
8bits output |
163 fps |
| 10bits output |
| 12bits output |
51.5 fps |
| Shutter Type |
Global |
| ADC bit width |
12bits |
| Video Format |
8bits / 10bits / 12bits output |
| Noise Level |
8bits output |
Less than 3 digits (Gain 0 dB) |
| 10bits output |
Less than 12 digits (Gain 0 dB) |
| 12bits output |
Less than 48 digits (Gain 0 dB) |
| Sensitivity |
1160 Lux (Typical) |
570 Lux (Typical) |
| Exposure time |
8bits output |
33.12 µseconds to 81.3 seconds (Default: 23,386.4 µseconds) |
| 10bits output |
| 12bits output |
38.62 µseconds to 104.3 seconds (Default: 29,880.3 µseconds) |
| Gain |
Analog |
0 to 20.8 dB (Default: 0 dB) |
| Digital |
x1 to x2 (Default: x1) |
| Black Level |
8bits output |
0 to 31 digits |
| 10bits output |
0 to 127 digits |
| 12bits output |
0 to 511 digits |
| White Balance Gain |
0 (Black level) to x3.99 (Default: x1) |
N/A |
| ROI |
Horizontal: 32 to 1,920 pixels / Vertical: 32 to 1,200 lines (Default: 1,920 × 1,200)
Adjustable Steps for size: 16 pixels in horizontal direction / 4 lines in vertical direction
Adjustable Steps for offset: 2 pixels in horizontal direction / 2 lines in vertical direction |
| Multi ROIs |
16 regions (Horizontal 4 regions × vertical 4 regions) (Default: 1 region) |
| Gamma |
Gamma Table = 0.1 to 4.0 (Default = 1.0) |
| Binning |
N/A |
Individual x2 Horizontal, x 2 Vertical Binning /
Off
(Horizontal: Average, Vertical: Addition) |
| Decimation |
Individual x2 Horizontal, x2 Vertical Decimation / Off |
| Image Flip |
Horizontal / Vertical / Horizontal and Vertical / Off |
| Defective Pixel Correction |
Up to 64 points |
| Auto Image Control |
Auto Exposure |
Support |
Support |
| Auto Gain |
Support |
Support |
| Auto White Balance |
Support |
N/A |
| Operational Mode |
Edge preset Trigger / Pulse width Trigger / Start Stop Trigger / Free run |
| User Setting Storage |
Support |
| Communication |
Through USB3.0 bus |
| Interface |
USB3.0 Super speed (USB3.0 Micro B) |
| Protocol |
USB3 Vision® 1.0.1, GenICam Standard Version (SFNC 2.2, PFNC 2.0) compliant
and Sentech’s original protocol (on Standard SDK, Trigger SDK) |
| Input / Output |
Three GPIOs, One Camera Hardware Reset |
| Power |
Input Voltage |
+5V(typ.)(Conform to USB Standard) |
| Consumption |
Less than 4.0 W |
| Dimensions |
28 (W) × 28 (H) × 40 (D) mm *Excluding connectors→Drawing |
| Optical Filter |
IR Cut Filter |
No IR Cut Filter |
| Optical Center Accuracy |
Positional accuracy in Horizontal and Vertical directions: +/- 0.3 mm
Rotational accuracy of Horizontal and Vertical: +/- 1.5 deg. |
| Material |
Aluminum alloy (AC) |
| Lens Mount |
C Mount |
| Interface Connectors |
USB Connector: USB3.0 MicroB type
I/O Connector:HR10A-7R-6PB (Hirose)or equivalent |
| Camera Mounting |
M2 screw holes (Three on top, bottom and both side plate)
M4 screws holes (Two on top, four on bottom plate) |
| Weight |
Approximately 48g |
| Operational Temperature / Humidity |
Minimum |
Environmental Temperature: 0 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation) |
| Maximum |
Camera housing temperature (top plate) shall not exceed 60 deg. C |
| Storage Temperature/ Humidity |
Environmental Temperature: -30 to +70 deg. C,
Environmental Humidity: 0 to 85 %RH (No condensation) |
| Vibration |
20 Hz to 200 Hz to 20 Hz (5 min. / cycle), acceleration 10 G, XYZ 3 directions 30 min. each |
| Shock |
Acceleration 38 G, half amplitude 6 ms, XYZ 3 directions 3 times each |
| Standard Compliancy |
EMS: EN61000-6-2, EMI: EN55011 |
| RoHS |
RoHS Compliant |
|
| Camera settings |
Simple Setting |
▪Gain(Auto,Manual)
▪Shutter(Auto,Manual)
▪White Balance(Auto,Manual)
▪Mirror Image(Off,Horizontal,Vertical,Horizontal and Vertical)
▪Hue/Saturation(OFF,value)
▪Gamma(OFF,value)
▪Sharpness(OFF,value)
|
| Advanced Setting |
▪Gain/Shutter(ALC Mode,Fixed Gain,Fixed Shutter,Digital Gain)▪White Balance(AWB,Manual)
▪Gamma(Gamma Mode,Sharpness,Digital Clamp)▪Color(Hue▪Saturation▪color correction matrix)
▪Color gamma(R Gamma,Gr Gamma,Gb Gamma,B Gamma)▪Defect pixel correction▪Trigger▪EEPROM
▪Other(Scan mode,V Blanking for FPS,Still Image Pixel Format,Color interpolation,Mirror image,Rotation▪Display Mode)
|
USB Camera Software
StCamSWare |
▪Freeze▪Live Video▪Rename Camera▪Setting▪Size▪Call Back(Grid,Ellipse,Ellipse,FPS,Logo,Frames Received)
▪Snap Shot▪Video Capture
▪Draw(Line,Rectangle,Oval,Character string,Measures angles,Polygons,Perpendicular lines,Arch,Bezier curve,Cross)
|
Software Development Kit
Standard SDK / Trigger SDK
StCam_SDK |
▪Function library , Sample programs(Programming Examples)
▪Development platform : Visual C++6.0 , Visual Basic 6.0 , Visual C#++.NET 2003 , Visual C++.NET 2003,Visual Basic.NET2003
|
|
 |
(A)USB Connector:USB3.0 micro-B Type
(B)I/O Connector:HR10A-7R-6PB
(Hirose) or equivalent
Use mating connector HR10A-7P6S (Hirose) or equivalent
*Possible Maximum Rated Voltage is +24 V on CAM_RESET, GPIO0, GPIO1 and GPIO2.
*Please set "OPEN" electrically on N.C. (Pin 6).
|
|
|
|
|
|
■Cable with lock screw for USB 3.0 and cable with robot cable specifications are available.
|
 |
| Model No. |
Connector Configuration |
Length |
| NU3MBASU3S-2m |
USB 3.0 MicroB, with camera-side fastening screws |
2m |
| NU3MBASU3S-3.5m |
USB 3.0 MicroB, with camera-side fastening screws |
3.5m |
| NU3MBASU3B-3.5m |
USB 3.0 MicroB, with camera-side fastening screws, robot cables |
3.5m |
|
|
|
|
|
|
|
